Metrolab MagVector™ MV2 Digital 3-axis Hall Magnetic Sensor

The MagVector™ MV2 is the ideal solution if you need to integrate a sophisticated magnetometer into your electronic system. A typical application would be a sensor array for a custom magnetic field-mapping system.

Metrolab uses the same sensor in several of its products, and is now making this technology available to electronic systems designers. Note that, being an electronic peripheral component, the MagVector™ MV2 includes none of the amenities of a traditional magnetometer: the user must supply the micro-controller, control firmware, host interface, user interface, and, last but not least, calibration. For complete 3-axis Hall magnetometers, please see the THM1176 / TFM1186 family of instruments.

Small but powerful

MV2 Block diagramMeasuring only 3x3x0.9 mm, the MagVector™ MV2 is a powerful magnetometer on a chip: three orthogonal Hall sensors measure (Bx,By,Bz); the “spinning current” technique minimises noise, offset and the Planar Hall Effect; a built-in temperature sensor permits temperature compensation; a programmable-gain amplifier provides measurement ranges from 0.1 to 30 T; and built-in ADCs and SPI (Serial Peripheral Interface) provide a digital interface in addition to an analog one.

High performance

The MV2 features a noise density of 300 nT/√Hz and an analog measurement bandwidth of 50 kHz. In digital mode, measurement rate can be traded off against ADC resolution, ranging from 0.375 to 3 kHz, and from 14 to 16 bits, respectively. It supports a supply voltage of 3.3 or 5 V. The compact 3×3 mm QFN package is completely nonmagnetic, compatible with MRI environments. Please see the Data Sheet for details.

Analog and digital interfaces

A signal pin selects between the analog or digital interface. In analog mode, configuration options such as the measurement range are selected using control signals, whereas in digital mode all configuration parameters are transferred via SPI and stored in internal registers. Additional control signals and register bits provide fine control over the measurement process, for example the timing of the analog/digital conversion. In digital mode, multiple MV2s can be connected to a single SPI bus.

MV2 Application diagram analog

Accessories

MagVector™ MV2 Evaluation Kit

The MagVector™ MV2 Evaluation Kit provides a flexible turnkey hardware and software environment that allows all features of the MagVector™ MV2 to be exercised.

The kit consists of:

  • Test board with MagVector™ MV2 sensor
  • Preprogrammed Arduino board that connects to the test board
  • Arduino firmware to drive the MagVector™ MV2, including source code
  • Host software to exercise the MagVector™ MV2, including source code
  • Two unmounted MagVector™ MV2 sensors.

Pricing

Part No.DescriptionQtyPriceIn Stock
MV2

MagVector Three-Component IC with Analog and Digital output, +/-100mT to +/-30T

1+
10+
25+
50+
100+
$900
$600
$480
$390
Ask
Quantity Price
1 $900.00
2 $900.00
3 $900.00
4 $900.00
5 $900.00
6 $900.00
7 $900.00
8 $900.00
9 $900.00
10 $600.00
11 $600.00
12 $600.00
13 $600.00
14 $600.00
15 $600.00
16 $600.00
17 $600.00
18 $600.00
19 $600.00
20 $600.00
21 $600.00
22 $600.00
23 $600.00
24 $600.00
25 $480.00
26 $480.00
27 $480.00
28 $480.00
29 $480.00
30 $480.00
31 $480.00
32 $480.00
33 $480.00
34 $480.00
35 $480.00
36 $480.00
37 $480.00
38 $480.00
39 $480.00
40 $480.00
41 $480.00
42 $480.00
43 $480.00
44 $480.00
45 $480.00
46 $480.00
47 $480.00
48 $480.00
49 $480.00
50 $390.00
51 $390.00
52 $390.00
53 $390.00
54 $390.00
55 $390.00
56 $390.00
57 $390.00
58 $390.00
59 $390.00
60 $390.00
61 $390.00
62 $390.00
63 $390.00
64 $390.00
65 $390.00
66 $390.00
67 $390.00
68 $390.00
69 $390.00
70 $390.00
71 $390.00
72 $390.00
73 $390.00
74 $390.00
75 $390.00
76 $390.00
77 $390.00
78 $390.00
79 $390.00
80 $390.00
81 $390.00
82 $390.00
83 $390.00
84 $390.00
85 $390.00
86 $390.00
87 $390.00
88 $390.00
89 $390.00
90 $390.00
91 $390.00
92 $390.00
93 $390.00
94 $390.00
95 $390.00
96 $390.00
97 $390.00
98 $390.00
99 $390.00
100+ $0.00
MV2-Eval

Evaluation Kit, MagVector MV2 Three-Component IC contains:

  • Test board with MagVector™ MV2 sensor
  • Preprogrammed Arduino board that connects to the test board
  • Arduino firmware to drive the MagVector™ MV2, including source code
  • Host software to exercise the MagVector™ MV2, including source code
  • Two unmounted MagVector™ MV2 sensor
1+ $,1870

Terms and Conditions

Terms and Conditions:

Prices above are for domestic deliveries to Canada, USA and Mexico only.
For deliveries in all other countries please contact Metrolab.
Prices are expressed in U.S. Dollars, FCA San Carlos, California.
Prices are subject to change without notice.
OEM discounts are available.

Payment:

Visa, MasterCard, Amex, Prepayment before shipment, or Net 30 days (subject to credit acceptance).

Delivery:

30 to 120 days.